Rear Inlet
The rear module acts as a part cooling fan inlet. Use the single 5015 inlet if you are unsure which is best.
15mm CPAP
v3
General Notes
This inlet accepts a 15mm ID CPAP hose, secured by zip ties.
CPAP hoses typically come with a latching mechanism on each end; these must be removed.
| Type | Part | Qty |
|---|---|---|
| Printed | rear_inlet_15mm_cpap.stl | 1 Ea |
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 912 | M3 x 6mm SHCS | 1 Ea |
| DIN 127 | M3 Split Lock Washer | 5 Ea |
| Other | 15mm CPAP Hose | 1 Ea |
| Other | Zip Tie 100mm/4" | 2 Ea |
v3
General Notes
This inlet accepts a 15mm ID CPAP hose, secured by zip ties.
CPAP hoses typically come with a latching mechanism on each end; these must be removed.
Variant Notes
- The inlet uses a flat head cap screw to secure the duct to the bottom horns.
screw_cap.stlis used to cover the screw so that it cannot loosen and contact the Beacon connector.- Do not use a flat head screw longer than 5mm with Beacon RevH.
| Type | Part | Qty |
|---|---|---|
| Printed | rear_inlet_15mm_cpap_beacon.stl | 1 Ea |
| Printed | screw_cap.stl | 1 Ea |
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 7991 | M3 x 5mm FHCS | 1 Ea |
| DIN 127 | M3 Split Lock Washer | 4 Ea |
| Other | 15mm CPAP Hose | 1 Ea |
| Other | Zip Tie 100mm/4" | 2 Ea |
Dual 5015 Rear Inlet
General Notes
This rear inlet is modified from the stock 5015. It offers plenty of airflow at the cost of a larger toolhead in the Y and Z axes.
Materials
| Type | Part | Qty |
|---|---|---|
| Printed | dual_5015_inlet.stl | 1 Ea |
| DIN 912 | M3 x 20mm SHCS | 2 Ea |
| Fan | 50mm x 15mm Radial Blower | 2 Ea |
| DIN 125 | M3 Washer | 2 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 2 Ea |
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 912 | M3 x 6mm SHCS | 1 Ea |
| DIN 127 | M3 Split Lock Washer | 5 Ea |
Heat Set Insert Locations
Dual 5015 Rear Inlet (Owl's Eyes)
0.3
General Notes
This is a (vertically) lower-profile option than the regular dual inlet. Depending on your configuration, it may also offer additional Y-axis space.
| Type | Part | Qty |
|---|---|---|
| Printed | rear_dual_5015_owl_eyes.stl | 1 Ea |
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 912 | M3 x 6mm SHCS | 1 Ea |
| DIN 127 | M3 Split Lock Washer | 5 Ea |
| DIN 912 | M3 x 20mm SHCS | 2 Ea |
| Fan | 50mm x 15mm Radial Blower | 2 Ea |
| DIN 125 | M3 Washer | 2 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 2 Ea |
Heat Set Insert Locations
0.3
General Notes
This is a (vertically) lower-profile option than the regular dual inlet. Depending on your configuration, it may also offer additional Y-axis space.
Variant Notes
- The inlet uses a flat head cap screw to secure the duct to the bottom horns.
screw_cap.stlis used to cover the screw so that it cannot loosen and contact the Beacon connector.- Do not use a flat head screw longer than 5mm with Beacon RevH.
| Type | Part | Qty |
|---|---|---|
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 127 | M3 Split Lock Washer | 4 Ea |
| DIN 7991 | M3 x 5mm FHCS | 1 Ea |
| Printed | screw_cap.stl | 1 Ea |
| Printed | rear_dual_5015_owl_eyes_beacon.stl | 1 Ea |
| DIN 912 | M3 x 20mm SHCS | 2 Ea |
| Fan | 50mm x 15mm Radial Blower | 2 Ea |
| DIN 125 | M3 Washer | 2 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 2 Ea |
Heat Set Insert Locations
Rear Intake Adapter
v0.1
General Notes
The rear intake adapter allows stock EVA rear inlets to be used, or any mods based on them.
Materials
| Type | Part | Qty |
|---|---|---|
| Printed | stock_intake_adapter.stl | 1 Ea |
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 127 | M3 Split Lock Washer | 4 Ea |
Single 5015 Rear Inlet
0.2
General Notes
This is an excellent all-purpose cooling option. Use this if you aren't sure which inlet to use.
| Type | Part | Qty |
|---|---|---|
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 912 | M3 x 6mm SHCS | 1 Ea |
| DIN 127 | M3 Split Lock Washer | 5 Ea |
| Printed | rear_inlet_single_5015.stl | 1 Ea |
| DIN 912 | M3 x 20mm SHCS | 1 Ea |
| Fan | 50mm x 15mm Radial Blower | 1 Ea |
| DIN 125 | M3 Washer | 1 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 1 Ea |
Heat Set Insert Locations
0.2
General Notes
This is an excellent all-purpose cooling option. Use this if you aren't sure which inlet to use.
Variant Notes
- The inlet uses a flat head cap screw to secure the duct to the bottom horns.
screw_cap.stlis used to cover the screw so that it cannot loosen and contact the Beacon connector.- Do not use a flat head screw longer than 5mm with Beacon RevH.
| Type | Part | Qty |
|---|---|---|
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 127 | M3 Split Lock Washer | 4 Ea |
| DIN 7991 | M3 x 5mm FHCS | 1 Ea |
| Printed | screw_cap.stl | 1 Ea |
| Printed | rear_inlet_single_5015_beacon.stl | 1 Ea |
| DIN 912 | M3 x 20mm SHCS | 1 Ea |
| Fan | 50mm x 15mm Radial Blower | 1 Ea |
| DIN 125 | M3 Washer | 1 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 1 Ea |
Heat Set Insert Locations
Single 5015 Rear Inlet, EVA-Style
Materials
| Type | Part | Qty |
|---|---|---|
| Printed | rear_5015_inlet.stl | 1 Ea |
| DIN 912 | M3 x 20mm SHCS | 1 Ea |
| Fan | 50mm x 15mm Radial Blower | 1 Ea |
| DIN 125 | M3 Washer | 1 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 1 Ea |
| DIN 912 | M3 x 45mm SHCS | 4 Ea |
| DIN 912 | M3 x 6mm SHCS | 1 Ea |
| DIN 127 | M3 Split Lock Washer | 5 Ea |
Heat Set Insert Locations
Single Papst RLF35-8
General Notes
This is an intake for a high-flow Papst RLF35-8 radial blower.
Note
This inlet requires several flat head cap screws.
| Type | Part | Qty |
|---|---|---|
| DIN 912 | M3 x 6mm SHCS | 1 Ea |
| DIN 127 | M3 Split Lock Washer | 3 Ea |
| Printed | rear_inlet_single_papst_rlf35.stl | 1 Ea |
| Fan | Papst RLF35-8 | 1 Ea |
| DIN 125 | M3 Washer | 2 Ea |
| DIN 912 | M3 x 20mm SHCS | 2 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 2 Ea |
| DIN 912 | M3 x 45mm SHCS | 2 Ea |
| DIN 7991 | M3 x 45mm FHCS | 2 Ea |
Heat Set Insert Locations
General Notes
This is an intake for a high-flow Papst RLF35-8 radial blower.
Note
This inlet requires several flat head cap screws.
Variant Notes
- The inlet uses a flat head cap screw to secure the duct to the bottom horns.
screw_cap.stlis used to cover the screw so that it cannot loosen and contact the Beacon connector.- Do not use a flat head screw longer than 5mm with Beacon RevH.
| Type | Part | Qty |
|---|---|---|
| DIN 7991 | M3 x 5mm FHCS | 1 Ea |
| Printed | screw_cap.stl | 1 Ea |
| Printed | rear_inlet_single_papst_rlf35_beacon.stl | 1 Ea |
| Fan | Papst RLF35-8 | 1 Ea |
| DIN 125 | M3 Washer | 2 Ea |
| DIN 912 | M3 x 20mm SHCS | 2 Ea |
| Other Fastener | M3 x 5mm OD x 4mm L Insert | 2 Ea |
| DIN 912 | M3 x 45mm SHCS | 2 Ea |
| DIN 127 | M3 Split Lock Washer | 2 Ea |
| DIN 7991 | M3 x 45mm FHCS | 2 Ea |
Heat Set Insert Locations